auggie
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
Hopefully that's the cause of the bad IS. If not, back to square one.
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
I will just replace both at this point, sigh...
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
I just did one final check. took out the right linear rail because that seems to bind up more. Place it on a table and move the carriage with my hand, unfortunately at the spots that always bind up with the gantry, it feels rough and occasionally causes the carriage to slip off my finger because it got momentarily stuck
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
Me too 😭
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
Before changing to lithium grease, I was using sewing machine oil, same issue hence ripping everything apart and cleaned it
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
1. The right carriage is missing 1 ball bearing and each side of the carriage
2. I am leaning towards this, it's ocurring at sinilar spots
3. Yes, aligned to the front, xy plate is squared
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
Disconnected belts from the back, loosened front, still seize/jam when I move it rapidly
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
And it seems to be always the same spot
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
I am so tired from all the experimentation today
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
I have not tried removing the belt, will do that next
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
Toolhead able to move left and right
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
At this point, I really just want to give up... Cleaned the rails, took out the bearings, cleaned up. Lubricated it with white lithium grease. End up still seizing up when I move y axis rapidly
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
I am able to seize up my carriage repeatedly by rapidly moving my toolhead up and down in the diagonal (45deg) direction. Initially thought that it was due to the belt binding somewhere but realized I am still able to move the toolhead in the x direction but not the y direction.
I suspect that it's the bearings in mgn12 blocks on the y linear rails seizing up/jamming. Gonna try lubing it with white lithium grease without dismantling. If it helps but still causes jamming randomly, I will have to fully dismantle and clean the bearings in the block. Suspect it may be dog hairs getting in the block haha
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
I am beginning to figure out what's wrong
65 replies
RRCRat Rig Community [Unofficial]
•Created by auggie on 5/27/2024 in #fix-my-resonance
Spike in y shaper at 80hz to 100+ hz
Already did that, I have a feeling the binding is coming from my BRS m1 mod
65 replies