Azzkikkr
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 2/18/2025 in #ratos-support
Belt tension graph interpretation help
Thanks, @MDFPereira I'll give that a try. So, essentially the belt with the lower PSD reading needs more tension?
6 replies
RRCRat Rig Community [Unofficial]
•Created by Arthur_C on 1/27/2025 in #ratos-support
Error during accelerometer data streaming
While I'm at it, I think I'm going to try and reinstall RatOS 2.1 to see if that fixes it. There is an open GitHub issue for RatOS 2.1 installation where if you follow the directions and update the RatOS packages before finishing configuration, you get a 502 gateway error when trying to access the configurator and to work around it you have to finish the configuration and setup completely before updating the RatOS packages. I wonder if that has something to do with it
24 replies
RRCRat Rig Community [Unofficial]
•Created by Arthur_C on 1/27/2025 in #ratos-support
Error during accelerometer data streaming
@Arthur_C no change here. My printer is currently out of commission as I'm replacing the belts and pulleys. I noticed VFAs in my print and no amount of tension adjustment corrected it. I wanted to use the RAT to check resonance during a print, but it's been non functional this entire time
24 replies
RRCRat Rig Community [Unofficial]
•Created by Arthur_C on 1/27/2025 in #ratos-support
Error during accelerometer data streaming
Unfortunately, I don't have a toolboard on this printer. It's just the beacon. I can try installing a separate ADXL345 to see if that works
24 replies
RRCRat Rig Community [Unofficial]
•Created by Arthur_C on 1/27/2025 in #ratos-support
Error during accelerometer data streaming
I upgraded to RatOS 2.1 yesterday and after upgrading, I tried the analysis tool but it never worked.
24 replies
RRCRat Rig Community [Unofficial]
•Created by Arthur_C on 1/27/2025 in #ratos-support
Error during accelerometer data streaming
24 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
Sounds good. I noticed the printer still did the adaptive meshing before starting the print, so I'm not too worried. Thanks again!
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
That's the python script added to Cura to obtain the X0, X1, Y0, and Y1 coordinates from the G-Code for adaptive meshing. The RatOS documentation has all this info
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
Understood. Thanks for your time
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
Yes, non-IDEX
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
When I tried the print without these variables, I got an error message that the G-Code generator was not valid
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
These two variables were set based on recommendations by Helge
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
Oh ok... here it is
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
Sounds good. Thank you!~
38 replies
RRCRat Rig Community [Unofficial]
•Created by Azzkikkr on 1/27/2025 in #ratos-support
Print Start shows a warning about incomplete Slicer configuration.
Oh, yes I did. For Cura I added the MeshPrintSize.py script and added that as post processing script in Cura
38 replies