Scootworks
Scootworks
RRCRat Rig Community [Unofficial]
Created by Scootworks on 8/31/2024 in #ratos-support
Change Wifi Settings for another network
aaah, I usually added the credentials on the rpi imager, so it was never an issue. good to know that. thank you
5 replies
RRCRat Rig Community [Unofficial]
Created by Mr. Hye on 4/28/2024 in #fix-my-print
Rough artifacts on surface
oh no, sad to hear that
61 replies
RRCRat Rig Community [Unofficial]
Created by Mr. Hye on 4/28/2024 in #fix-my-print
Rough artifacts on surface
are you using the correct configs for the extruder?
61 replies
RRCRat Rig Community [Unofficial]
Created by Mr. Hye on 4/28/2024 in #fix-my-print
Rough artifacts on surface
I'm not sure, but could it be that the filament is slipping at the extruder? what happens if you set the volumetric speed just to a third of the current value?
61 replies
RRCRat Rig Community [Unofficial]
Created by Mr. Hye on 4/28/2024 in #fix-my-print
Rough artifacts on surface
I‘m just wondering what happens, if you run a VFA test
61 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
nö, ich müsste mich aber auch mal schlau machen wie der sensor fürs proben funktioniert, den du da aktuell verbaut hast
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
No description
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
@Serdar1976 aber nicht zu vernachlässigen ist auch diese Info
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
sehr schön. ja der 55er wert ist also die basis, das feintuning machst du wie gesagt mit diesen 110mm. gib bescheid wenn was unklar ist, dann mache ich sonst ein video
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
gerne 🙂
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
das hat zwar keinen einfluss auf dein problem, aber wenn man schon bei der config was ändert, kann man das gleich reinnehmen
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
0.04 ist in den meisten fällen ok
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
oh, was ich auch gerade gesehen habe 'pressure_advance_smooth_time: 0.02' würde ich eher auf 0.04 setzen. bei 0.02 sagt mein bauchgefühl, dass es zu niedrig ist
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
No description
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
aber ja, bitte gerngeschehen 🙂
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
dann wird auch dein durchmesser der extrudierten masse kleiner
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
deine rotation distance ist eh bissl daneben... so wie ich es verstehe, gemäss diesem datenblatt, müsste es bissl anders sein. ich könnte mir vorstellen, dass die rotation_distance 55 sein könnte
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
No description
95 replies
RRCRat Rig Community [Unofficial]
Created by Serdar1976 on 5/11/2024 in #german-support
extrusion Ursache unklar
No description
95 replies