Bagellord
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
Print was successful. So once I get the USB camera sorted out I'll get it back together, back in place, and make sure the leveling feet have good contact and are locked in
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
Well there's still a bit of unevenness in my test squares, but it's close enough that I am doing a print using most of the bed, for a multiboard tile that I need. We'll see how that goes
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
I am running the compensation mesh now just to see how it does. I've got to go get a different cable for my chamber camera before I can button the whole thing back up
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
I figured haha. Now I just have to summon the energy to lift this thing by myself. It's not light, I can't imagine the larger variants
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
Oh heck no. $2 pavers on top of plywood
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
It sits on top of some paving stones at the bottom of my printer shelf, so I have to take it out to get the panels off
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
That was gronking on the X gantry a touch. I've got to get the side panels back on and then put the printer back into its cubby hole
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
Nice.
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
If you can find that, that'd be great.
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
I wouldn't chase it if I wasn't suspecting issues is the problem, because i'll have perfect squish at the front and then it's too close at the back, even with a mesh. So it leads me to believe something isn't flat or aligned properly
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
Usually I put the door on, and leave the top popped open
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
Right now I am doing PLA with a 65 degree bed, it's enclosed
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
I had not thought about needing to adjust the feet. I will try that. I've been messing with the gantry and pulled up on the X beam a bit, which got it down. I've just been getting some inconsistent Z with the back of the plate being closer than the front
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
Here's the most recent mesh
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
What angle is best for this? I am running a mesh right now
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
Also, that second image is has the rear of the printer on the left and the front of the printer on the right - basically a side view, not head on
41 replies
RRCRat Rig Community [Unofficial]
•Created by Bagellord on 9/16/2024 in #fix-my-mesh
V-Core 4 300 - Do I need to work on my gantry more?
Is that not correct?
41 replies