DollaTom
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/10/2023 in #ratos-support
Flash stock - Extruder not heating at expected rate
Yeah it completed and didn't throw any of the errors
15 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/10/2023 in #ratos-support
Flash stock - Extruder not heating at expected rate
I reseated my hotend thermistor and heater cables and it's progressing further than it used to
15 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/10/2023 in #ratos-support
Flash stock - Extruder not heating at expected rate
Thanks all
15 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/10/2023 in #ratos-support
Flash stock - Extruder not heating at expected rate
I think I would like to upgrade though, is there a commonly recommended bigger wattage?
15 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/10/2023 in #ratos-support
Flash stock - Extruder not heating at expected rate
I'll hook everything back up and run some more tests.
15 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/10/2023 in #ratos-support
Flash stock - Extruder not heating at expected rate
I did not. I'm very very new to this as you very well must be able to tell.
15 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/10/2023 in #ratos-support
Flash stock - Extruder not heating at expected rate
I see now I was thinking at a bit too low a level. I think there's a workflow from prusaslicer for it
15 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
More research suggests none of this is relevant and it's applying a mesh automatically at the beginning regardless.
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
There are user reports of that all over the internet so it seems intended? I'm not sure how to run a leveling calibration print with the mesh applied.
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
Running a home all seems to crash the carriage unless I unload the mesh and home from that point.
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
It's pretty clear my bed has some slight skew to it and it seems like a mesh should compensate quite well, but when attempting to start a print with a mesh loaded I get an error:
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
Hey I can pop into another channel if this question is more applicable but I'm now working on bed leveling of course (natural flow of things) and I'm new enough to 3D printing that I don't know if this is me trying to do something nonsensical or a misconfiguration.
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
So much respect y'all
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
I'll be able to figure it out with that
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
I searched the docs but I couldn't find instructions on setting up a webcam?
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
wowww the dashboard looks cool all populated
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
you guys are fucking great
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
I did so, it completed
308 replies
RRCRat Rig Community [Unofficial]
•Created by DollaTom on 3/8/2023 in #ratos-support
Support for Prusa MK3S+
308 replies