Vycrone
Vycrone
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
Thank you very much for your help!
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
I have not enclosed it yet, but I will update this thread if anything pops up!
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
I have a self sourced power supply and SSR which is likely why I am having a lot of electrical noise as they are likely not as high quality as the ratrig ones.
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 10/27/2024 in #fix-my-printer
Beacon Bed Level Sensor not having enough accuracy whilst bed is at temperature.
Thank you very much for all your help @Arthur_C and @TheTik
34 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 10/27/2024 in #fix-my-printer
Beacon Bed Level Sensor not having enough accuracy whilst bed is at temperature.
However @miklschmidt explained the cause of the issue and helped come up with a solution. I have explained it in the Ratos-Support thread here: https://discord.com/channels/582187371529764864/1302778490692829217
34 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 10/27/2024 in #fix-my-printer
Beacon Bed Level Sensor not having enough accuracy whilst bed is at temperature.
I am not drawing any more power than the 3 USB cables that were supplied in the kit, the EBB42 V1.2 board the octopus V1.1 and the beacon.
34 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
That is the line that I added to printer.cfg
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
No description
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
The watermark I set the delta to 3­°C, this allowed the probing to occur when the heater was off, I then searched up whether there was a function to turn the heater off during probing and Klipper does have this function built in.
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
No description
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
No description
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
I have found a solution to the issue based on your comments about the SSR, I understand that this will likely add more noise into my printer that could cause other issues down the line, however I will deal with this when I get there.
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
so clearly the hotend and the bed are both causing issues, however the Bed is creating more issues
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
No description
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
No description
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
Would decreasing the pwm frequency on the bed/hotend help at all? Or would another option be shielding the wires better?
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
I will have a look, thank you!
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 11/3/2024 in #ratos-support
Initial approach of beacon not working when the heated bed or hotend is heating.
I am not using the one recommended by ratrig, so that might be the issue.
39 replies
RRCRat Rig Community [Unofficial]
Created by Vycrone on 10/27/2024 in #fix-my-printer
Beacon Bed Level Sensor not having enough accuracy whilst bed is at temperature.
Thank you very much for your reply, I have elevated the issue to the ratos-support thread. I saw some potential issues there but I haven't found the solution yet
34 replies