Lemcott
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
these are super basic
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
how do you unload? just the unload macro or retract a bunch or manually or?
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
anyway, still, on a rapido I'll have heat cranked and just rip it out and never really have an issue, so maybe something is up with your heatbreak
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
I guess a lot of tip forming macros do this
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
I like... kinda just always have done this? but I've never really seen it anywhere else.
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
when you unload first turn off the heat and then extrude 25-50mm while it is still hot, then quickly retract all the way out.
this helps purge the final end of the plastic that is already warm and by retracting immediately afterwards you can ensure the smallest amount of melted filament on the end of the tip
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
what you just said does not make sense
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
when is it jamming up
48 replies
RRCRat Rig Community [Unofficial]
•Created by Lemcott on 12/6/2024 in #ratos-support
WHY does my prnter.cgf keep booting up blank
rare, but definitely more than few times now
15 replies
RRCRat Rig Community [Unofficial]
•Created by Lemcott on 12/6/2024 in #ratos-support
WHY does my prnter.cgf keep booting up blank
iunno, I just boot up and... my leds don't come on. check printer.cfg and yep, blank again.
15 replies
RRCRat Rig Community [Unofficial]
•Created by Lemcott on 12/6/2024 in #ratos-support
WHY does my prnter.cgf keep booting up blank
nah, 2.0.2-27
15 replies
RRCRat Rig Community [Unofficial]
•Created by Lemcott on 12/6/2024 in #ratos-support
WHY does my prnter.cgf keep booting up blank
and I have a hard backup of all the important stuff
15 replies
RRCRat Rig Community [Unofficial]
•Created by Lemcott on 12/6/2024 in #ratos-support
WHY does my prnter.cgf keep booting up blank
I usually always have a recent delta file that I can just copy/paste into the blank one
15 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
retraction speeds/lengths?
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
I think my slowest overhang is still like 40, maybe 60. and I'm probably printing closer to 195
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
filament flowing through the block and nozzle is basically 'water cooling' you are using a liquid running through a system to absorb the heat and move it out, if that water is allowed to sit there on the hot point it will begin to boil
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
in a UHF at 210ish running pla I'd hope you were moving 100+mm/s, if not, we could just be moving too slow to allow all that heat to creep up.
48 replies
RRCRat Rig Community [Unofficial]
•Created by za_naimis on 12/7/2024 in #fix-my-printer
jammin is NOT okay, man. (filament regularly jams in heat break)
jams in the heatbreak are going to be one of two things:
- heatbreak is physically not set correctly and the filament is getting caught on something
- heat is too hot and the heatbreak gets warm enough to start melting plastic up in the break before it even gets to the block.
48 replies
RRCRat Rig Community [Unofficial]
•Created by Lemcott on 12/6/2024 in #ratos-support
WHY does my prnter.cgf keep booting up blank
not exactly brand new but shouldn't be that bad. I would assume other issues would be present than just one file going blank
15 replies