k1bbles
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/7/2025 in #fix-my-printer
IDEX layer shift
The other X stepper is for T1 so that'll be last - but T0 X, plus hybrid Y motors.
11 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/7/2025 in #fix-my-printer
IDEX layer shift
I'm going through them one by one right now
11 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/7/2025 in #fix-my-printer
IDEX layer shift
T0 belt stepper is locked down on the flat so it's not that. Trying to work belt tension now.
11 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/7/2025 in #fix-my-printer
IDEX layer shift
I have had a grub screw let loose before - I'll double check it that it's locked down.
11 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/7/2025 in #fix-my-printer
IDEX layer shift
11 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/7/2025 in #fix-my-printer
IDEX layer shift
Only T0, haven't heard any skipping noises at all but will recheck belt tension.
11 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/6/2025 in #fix-my-printer
IDEX Upgrade VCore 300
Then have to print the VAOC part that I thought would be included but, apparently, is not.
18 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/6/2025 in #fix-my-printer
IDEX Upgrade VCore 300
I dunno if I trust T1 to try printing with it but I think I can at least print with T0 again at this point once the beacon recalibrates.
18 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/6/2025 in #fix-my-printer
IDEX Upgrade VCore 300
Basically yes! Words to live by.
18 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/6/2025 in #fix-my-printer
IDEX Upgrade VCore 300
My own fault, I hadn't tucked the T1 cabling into a safe place and it got caught and pulled the usb-c out which crashed everything. Trying again without the stupidity.
18 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/6/2025 in #fix-my-printer
IDEX Upgrade VCore 300
Well that was fun - homed all axis and both tool heads zerod along with Z, went to do a beacon calibrate and the bed crashed.
18 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/6/2025 in #fix-my-printer
IDEX Upgrade VCore 300
Nope - reconfig seemed to find it. Thank god, those parts fans are so loud until the PWM pin comes online.
18 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/6/2025 in #fix-my-printer
IDEX Upgrade VCore 300
Is it possible T0 and T1 are reversed somehow? I guess I'd have to check the USB config.
18 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/6/2025 in #fix-my-printer
IDEX Upgrade VCore 300
Pi can see it:
18 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/6/2025 in #fix-my-printer
IDEX Upgrade VCore 300
Yes, on T0. T1 has no sensor.
18 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 4/6/2025 in #fix-my-printer
IDEX Upgrade VCore 300
The answer was I'm an idiot and tried to reuse my old config rather than "start fresh". So I'm past that now but now klipper is complaining about "Option 'serial' in section 'beacon' must be specified" -- which is new to me (everything worked great pre-IDEX!).
18 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 7/30/2024 in #fix-my-printer
Strange clicking sound on moves VCore4 300 Hybrid
Yeah I've noticed it less over the past day -- I did pick up some new bearings to have in my parts kit "just in case" though for later!
12 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 7/30/2024 in #fix-my-printer
Strange clicking sound on moves VCore4 300 Hybrid
Thankfully, if it is the idler I can easily swap those out and see. Looks like I'll be placing an order for some new ones!
12 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 7/30/2024 in #fix-my-printer
Strange clicking sound on moves VCore4 300 Hybrid
Best I'm able to tell it's the idler on the upper belt on the back right side. Not 100% sure but that seems the most likely culprit at this time. Just a clicking - brand new bearing that didn't seem to have any issues the first few days and suddenly getting clicking.
12 replies
RRCRat Rig Community [Unofficial]
•Created by k1bbles on 7/30/2024 in #fix-my-printer
Strange clicking sound on moves VCore4 300 Hybrid
I'll try that, thanks. Just started doing it this morning - was running fine since I finished assembling and tuning it over the last couple of days.
12 replies