Rewire
Rewire
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
All the belts are off right now
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
Takes less than a pound of force to straighten it I mean I can push on it with my pinky lightly and straighten it
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
No description
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
No description
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
So I loosened all the screws on the x Gantry and it's tilted by this much
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
sigh
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
it's not off on y, just x
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
ok
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
there is a tone coming from the motors while re-positioning, but if go to t0, and then back to t1, the motor tone is different
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
why then, is the motor tone different
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
reliably
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
so like, if i reset, it happens in the same spot
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
no no
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
I'm in VAOC right now, i align the nozzles, i click back to t0, its misaligned, then back to t1, its misaligned as well, but if i click back and forth between them, its misaligned in the same spot every time
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
So, i think there is something else going on here with VAOC.
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
Good toolhead z-offset of 0.028750mm! Your toolhead z-offset is good!
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
idex_xoffset = -1.0305952544778165
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
Very confusing. So center the nozzle where the metal ends.
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
No description
123 replies
RRCRat Rig Community [Unofficial]
Created by Rewire on 11/1/2024 in #ratos-support
gcode_macro _VAOC_CALIBRATE_Z_OFFSET:gcode'
No description
123 replies