Mike-Toro3D
RRCRat Rig Community [Unofficial]
•Created by Sid on 2/20/2025 in #ratos-support
PT1000 problem
There is a discourse post from mikl out there on the right configuration for the P1000 with a jumper
17 replies
RRCRat Rig Community [Unofficial]
•Created by Sid on 2/20/2025 in #ratos-support
PT1000 problem
What is thebPT configuration?
17 replies
RRCRat Rig Community [Unofficial]
•Created by Sid on 2/20/2025 in #ratos-support
PT1000 problem
Have you set any jumpers on your toolboard?
17 replies
RRCRat Rig Community [Unofficial]
•Created by Sid on 2/20/2025 in #ratos-support
PT1000 problem
Is the room temp at idle correct?
17 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
I'll DM you 😄
1877 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
Yes, in roughly 3 weeks 🙂
1877 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
If VisualTech is happy, then I am happy 😄
1877 replies
RRCRat Rig Community [Unofficial]
•Created by tg73 on 10/8/2024 in #fix-my-print
Regular surface distortion pattern towards end of larger first layers VC4
You would be the first person were it doesn't 😄
1877 replies
RRCRat Rig Community [Unofficial]
•Created by Nahkampfsocke on 12/6/2024 in #german-support
Unsauberkeiten?
Evtl zu nasses filament
9 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 12/22/2023 in #fix-my-printer
Loud rail sounds
You already found it, but for anyone looking for help check out my discord 🙂
I am not allowed to post a link, but you can find it in my vendor channel
10 replies
RRCRat Rig Community [Unofficial]
•Created by jupfi on 9/18/2024 in #fix-my-printer
Filament Jam with 10kg spool
Thank you 👍
10 replies
RRCRat Rig Community [Unofficial]
•Created by jupfi on 9/18/2024 in #fix-my-printer
Filament Jam with 10kg spool
What is a belay?
10 replies
RRCRat Rig Community [Unofficial]
•Created by Mike-Toro3D on 6/19/2024 in #german-support
Rapido 2 Heat Creep/Clogging
Danke für den Tipp. Ich hab mal gemessen: Bei 250°C laut Thermistor sind es 220°C außen an der Düse. Bei 280°C eingestellt sind es 260°C außen.
Ich habe jetzt auch mit dem Federstahldraht (1mm) das HE "gereinigt" - da hab ich freien Durchgang bis zur Düse (ich komme bis zur Düse ohne das der Draht irgendwo hängen bleibt)
Ich teste jetzt mal HIPS Filament (vorher war es ASA)
17 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #german-support
Heater_Bed not heating at expected rate
Ah ok, damit kenne ich mich nicht aus
13 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #german-support
Heater_Bed not heating at expected rate
Achso, dann ist vll. das SSR defekt
13 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #german-support
Heater_Bed not heating at expected rate
In 99% der Fälle ist es ein defekter Sensor/Wackelkontakt irgendwo
13 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #german-support
Heater_Bed not heating at expected rate
Zeit er plötzliche Einbrüche
13 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #german-support
Heater_Bed not heating at expected rate
Achso, ja das ist eher unwahrscheinlich. Wie sieht den der Graph aus?
13 replies
RRCRat Rig Community [Unofficial]
•Created by CeredD#77 on 5/28/2024 in #german-support
Heater_Bed not heating at expected rate
Oder hast du den auch getauscht?
13 replies