Xulkal Comments - Answer Overflow

back belts have 0.65mm of clearance, side belts have 1.15mm of clearance. So I only shimmed the Y to increase the back clearance as I felt the X had enough clearance already

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

Only shim the y

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

this would be the 5th time I've had to do that

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

I think it's belt related, and need to rerun new belts...but man that shit sucks

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

mine drifts based on build plate location

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

have you don't the box trick across the build plate?

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

I am partially tempted to go back to hybrid as I haven't really used idex lately. But that's probably more due to my rebuilding more than printing

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

I will say it's not much of an improvement pulling them forward, but I'm on a 300, so you might get different results.

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

Y already has 1mm or slightly more space

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

don't think it's necessary tbh. There's ~2.5mm of space from the belt to the PTFE holder, but ~0.65mm of space from the belt to the 3030...Just move the motor mounts forward using a 0.5 or 1.0mm spacer

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

but ya, mine has been gone for a while now

609 replies

RRCRat Rig Community [Unofficial]

•Created by TheBrigandier on 1/20/2025 in #fix-my-resonance

VC4 500 IDEX - 125hz Peak

trying to remember when I stopped seeing the ~125 bump I think it was reduced when I added more zipties to the toolhead wires and wire loom back to the enclosure

609 replies

RRCRat Rig Community [Unofficial]

•Created by 03Julian04 on 2/5/2025 in #fix-my-print

Different flow but same gcode

I am by far no expert in 3d printing I settle a lot for "good enough" and if I need better, I sand / wood putty fill, prime and paint

42 replies

RRCRat Rig Community [Unofficial]

•Created by 03Julian04 on 2/5/2025 in #fix-my-print

Different flow but same gcode

another possibility is drag on the filament due to ptfe routing

42 replies

RRCRat Rig Community [Unofficial]

•Created by 03Julian04 on 2/5/2025 in #fix-my-print

Different flow but same gcode

it depends, I've seen bad first layers fuck up infill which then fuck up top layers. over all your parts look good, just a few small indicators of problems that could come from quite a few different areas.

Gaming

Programming