ZIMZ
RRCRat Rig Community [Unofficial]
•Created by lingo124 on 2/6/2025 in #fix-my-printer
Lead Screw Screeching (Vcore4 IDEX)
I did the same. Took the noise away. Thank you.
10 replies
RRCRat Rig Community [Unofficial]
•Created by lingo124 on 2/6/2025 in #fix-my-printer
Lead Screw Screeching (Vcore4 IDEX)
On the top of the leadscrew?
10 replies
RRCRat Rig Community [Unofficial]
•Created by lingo124 on 2/6/2025 in #fix-my-printer
Lead Screw Screeching (Vcore4 IDEX)
I have this same issue, I lube it and it solves it. Usually only hear it during z tilt adjust. Did you solve it?
10 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 6/13/2024 in #fix-my-print
Vcore 4 endless ringing
Do you have a link to where you got the longer stepper pulleys? That sounds like a great idea!
78 replies
RRCRat Rig Community [Unofficial]
•Created by ~ bitbash on 1/28/2025 in #fix-my-resonance
Better results with Mirror/Copy than Single? 500 IDEX
Y needs more tension
5 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
Let me tinker with what I have now and I'll get back to you. I'm switching nozzles atm and I think I might be able to get better results.
1235 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
@tobi0892. yes and making sure VAOC was good for the x offset. I also had to mess with the endstops for T1. I'm hoping the processess gets easier
1235 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
Almost aligned but good enough for now
1235 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 1/1/2025 in #fix-my-printer
Bed level issue - wave in my bed mesh and copy / mirror prints on T1 result in waaaaaay to low z
@blacksmithforlife 🇺🇸 do you want me to remove the magnet?
16 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 1/1/2025 in #fix-my-printer
Bed level issue - wave in my bed mesh and copy / mirror prints on T1 result in waaaaaay to low z
I'll take it off and check, the issue is that I have the heater pad on the bottom and the magnet on the top so trying to do that is hard
16 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 1/1/2025 in #fix-my-printer
Bed level issue - wave in my bed mesh and copy / mirror prints on T1 result in waaaaaay to low z
16 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 1/1/2025 in #fix-my-printer
Bed level issue - wave in my bed mesh and copy / mirror prints on T1 result in waaaaaay to low z
16 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 1/1/2025 in #fix-my-printer
Bed level issue - wave in my bed mesh and copy / mirror prints on T1 result in waaaaaay to low z
There is a gap 🙂
16 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 1/1/2025 in #fix-my-printer
Bed level issue - wave in my bed mesh and copy / mirror prints on T1 result in waaaaaay to low z
will do
16 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 1/1/2025 in #fix-my-printer
Bed level issue - wave in my bed mesh and copy / mirror prints on T1 result in waaaaaay to low z
16 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 1/1/2025 in #fix-my-printer
Bed level issue - wave in my bed mesh and copy / mirror prints on T1 result in waaaaaay to low z
16 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 1/1/2025 in #fix-my-printer
Bed level issue - wave in my bed mesh and copy / mirror prints on T1 result in waaaaaay to low z
16 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 1/1/2025 in #fix-my-printer
Bed level issue - wave in my bed mesh and copy / mirror prints on T1 result in waaaaaay to low z
16 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
I added more tension and my y are both below 1% and x is 0%
110 replies
RRCRat Rig Community [Unofficial]
•Created by ZIMZ on 12/26/2024 in #fix-my-printer
Keenovo Heater pad not heating
@TheTik thank you. I'm going to put in a ticket to RR about both of them.
9 replies