Gri.fon
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
I apologize for my inattention
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
🫣
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
I found the problem, apparently by mistake they sent me Timing Pulley 16 Tooth
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
Unfortunately it doesn't work 🥺
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
parking in the home position remained also not in the center of the table
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
this is the last debug with this configuration
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
Will this configuration work correctly when printing from a slicer?
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
but with this configuration the print area is 450 x 450 in the printer configuration
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
because with a smaller value of position_max the head T0 does not reach the VAOC camera and I get an out of range error, I cannot complete the VAOC calibration because the head T1 when moving along X does not reach the VAOC camera and falls into an out of range error
31 replies
RRCRat Rig Community [Unofficial]
•Created by Gri.fon on 2/12/2025 in #fix-my-printer
Idex, parking not in the center
31 replies