WOPR73
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@miklschmidt yep. I think I am done for tonight. new error:Klipper reports: SHUTDOWN MCU 'mcu' shutdown: Timer too close
This often indicates the host computer is overloaded. Check
for other processes consuming excessive CPU time, high swap
usage, disk errors, overheating, unstable voltage, or
similar system problems on the host computer.
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown"
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@miklschmidt home x:250.00 y:250.00 z:15.00. Using paper test. x:250.00 y:250.00 z:0.20 the paper has some resistance.
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@miklschmidt yep, z must be off. "Probe samples exceed sample_tolerance"
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@miklschmidt hmm. I had it pass once before when it was just the aluminum sheety without the magnetic sheet and PEX bed wasnt installed.
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@miklschmidt yep, trying a non-PEX sheet now.
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@miklschmidt It has a PEX clear coat on the sheet and think there is to much room to move when doing the heated touch off part of the test.
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@miklschmidt I dont think it likes my wham bam flex sheet
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@miklschmidt errors like "6:14 PM Probe samples exceed sample_tolerance"
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@miklschmidt yeah, I was reading that in "https://os.ratrig.com/docs/configuration/#initial-configuration"
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@blacksmithforlife yep, understood. That's why I was asking for help. There is a lot of info on Z and motors going the wrong direction and how to fix it. But, there isnt alot on RatOS, Beacon, mainsail with properly running "BEACON_RATOS_CALIBRATE" but, an inverted Z.
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@blacksmithforlife are you sure that if I invert the Z's that it will not nose dive into my new bed when homing or running the beacon config. I understand that you say its mainsail and it very well might be, but I am to new to all of this to desern which is really mailsail vs klipper vs ratOS and which is going to effect the others.
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@blacksmithforlife never changed anything but, the extruder direction.
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@blacksmithforlife wut?
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@blacksmithforlife everything is default except changing the exturded direction. I removed the "!"
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@blacksmithforlife yes, if I press up the bed goes down, and if press down the bed goes up. But, "BEACON_RATOS_CALIBRATE" works how I would think it should. Moving the bed out of the way when untill needed to be checked for Z. then it bring the bed up and gets it reading then stops.
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@TheTik I changed the wording to clear things up.
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@blacksmithforlife nope I am good. i'll figure it out. just no magic smoke and ill be happy. Thanks!
428 replies
RRCRat Rig Community [Unofficial]
•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support
Unable to write tmc spi 'stepper_z' register GLOBALSCALER
@blacksmithforlife ah yes... they good old days. You could load am image and goto luch and it would be up once you get home.
428 replies