KaylebPrdelni
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
I have max set at 25mm³, then it starts skipping like mad with PLA at 230..
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
So, yeah, you're probably pushing little more than I do
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
Rapido and Lite Bondtech
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
Lemme check.. like i remember 🤣
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
Measured just under 2...
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
3sec. Just to be on the safe side
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
You can set spin up time in slicer, so it kicks off before it needs to
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
Tri horn is the thing that i believe did it for me. Through i did change the fan at the same time. But again, it's gone down in volume and speed, so that shouldn't be that...
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
Correcto mundo.
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
Brainfart on my end. Sorry.
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
😂
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
Words
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
There you go
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
Fan nozzle....
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
Oh. And one more thing. Ticking that Classic Mode box sometimes helps. Sometimes being the key part there..
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
In the end I changed the original nozzle for the one with extra flow. Made all the difference. Now it's presentable. Still, have to admit, I was expecting little better. One more thing I changed. Clumsy hands killed the killer fan it came with, so I changed over to Arctic 4028. It's much quieter, so it can run at faster baseline speed without too much annoyance. Full blast speed is lower, but honestly, I think the original fan is a bit overkill at the top end.
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
OK. filament brand makes no difference. Unless I go full blast on PLA overhangs they look horrid.
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
It might be filament in part I guess. I just tried printing at 80-100 fan for anything over 30deg . It looks decent then. I just find it ridiculous that I need such a volume of air for PLA. Sadly, with the results, I'm considering CPAP 😒
I'll try with different filament tomorrow. But don't have any other brand at hand, just different colors. Have some on order, so I guess I'll have to wait for concrete results a little longer.
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
what speeds are you printing at, if I may ask?
60 replies
RRCRat Rig Community [Unofficial]
•Created by KaylebPrdelni on 10/21/2023 in #fix-my-print
PLA overhangs are utter mess
60 replies