5jvm0u4
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
My problem is how can it be a old version after flashing with newest version of klipper installed, is it some problem of the board? Cause Mellow is notorious with their board quality
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
Tried flashing RatOS entirly and did the samething but without updating klipper via command line, same result.
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
I did it several times and every time is succeed but mainsail showed me the same error message, I tried git pull to manually update klipper via command line, and flash again, succeed and the same error message.
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
I did flash it using the command:
cd ~/klipper/
make menuconfig
make
cd && cd ~/klipper/
make flash FLASH_DEVICE=2e8a:0003
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
but I just flash it via ssh
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
it now says this
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
I want to install Mellow USB LIS2DW accel_chip but it kept saying "Section 'lis2dw' is not a valid config section"
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
got it, RatOS will try to center toolhead after homing, I got all of my motors reversed and implemented klipper_tmc_autotune, now things works... to some degree...
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
while tuning sensorless homing, it kept failing, and I found out that the G28 X is just performing a G1 move with accel and decel with the length of ~150mm and after movement it just call it homed, why??
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
Fun thing I found out, NOT related to RatOS though, while setting up CPAP control signal (require 2~50KHz PWM):
BTT Kraken only allow hardware PWM pin to be used with those that went through a buffer IC, so only for all the heater pins, and the fan pins.
And due to PCB designs, only those for heaters & 4-wire fan (Fan6's PA6 & Fan7's PE8) are available for actual hardware PWM "output", nowhere else is available.
Just in case if someone is doing the samething as I am, there you go.
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
I see, I'll try out Voron V0.1 to see if that works, thanks!
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
I see, I still have one question, how do I disable Z1 motor, to my understanding I can add and overwrite but not delete, is that right?
42 replies
RRCRat Rig Community [Unofficial]
•Created by 5jvm0u4 on 8/16/2024 in #ratos-support
VzBoT AWD + BTT Kraken config problems
Thanks for your reply! I'll try that out and report if I find anything worth noticing.
I've herd of RatOS will update it's config file automatically, from the newest release video, will I need to modify my file everytime to change it back then?
42 replies