Johnjrk
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
I did notice that after I ran the command line, rebooted and reran the setup wizard that my main board and toolhead boards wanted updated so there was something hung that I didn't notice.
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
Sorry to be that guy, I appreciate you!!!!
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
Well crap now it works, it just wanted me to look foolish 😂
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
standby...
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
You see it was there in the screenshot 🙂
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
You are right, cna I just paste it from my last config backup?
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
It was there, I just reran the setup wizard prior to posting.....
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
I didn't think that you would still be working on here, you need to get some rest!
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
Here you go
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
24 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/27/2024 in #fix-my-printer
Error evaluating 'gcode_macro _START_VAOC:gcode
24 replies
RRCRat Rig Community [Unofficial]
•Created by MonsieurLemon153 on 12/21/2024 in #fix-my-printer
Option 'allow_unknown_gcode_generator' is not valid in section 'ratos'
Thanks I had the same issue but your steps fixed it....
15 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 11/2/2024 in #ratos-support
Load Filament Macro Move Out of Range
Ok cool! glad you found it!
14 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 11/2/2024 in #ratos-support
Load Filament Macro Move Out of Range
I did have ddebug on but not sure where it stores the zip file?
14 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 11/2/2024 in #ratos-support
Load Filament Macro Move Out of Range
Console Output
14 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 11/2/2024 in #ratos-support
Load Filament Macro Move Out of Range
Console Output
14 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
Perfect thank you! Looking forward to my first print
58 replies
RRCRat Rig Community [Unofficial]
•Created by spacebaby0695 on 10/27/2024 in #ratos-support
VAOC T1 x not lining up
Ok that worked, thank you! And when I have them on target I just exit?
58 replies