Agony
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
1st is bed normal, second is bed turned 90
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
i opted for the 8mm milled bed too.... kinda worried/sad that it's too warped
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
in sort of that same pattern as the map
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
mm that is on a granite table in our QA department. the bed however you can see light with coming under my Starrett straight edge
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/27/2024 in #fix-my-mesh
v-core 4 500 idex 8mm bed
so i spun the PEI around, and sideways, and the variation is not much. 0.603 vs 0.584 vs 0.593 all looking about the same. also measured the gantry pre install with a drop gauge at work. got it divided into points: 0.00 0.05 0.06 0.07 0.07 0.08 0.09 0.08 0.08 0.07 0.05 0.02 0.01
34 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/20/2024 in #fix-my-printer
v-core 4 idex
it's working now! 2 new issues now! yay!
14 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/20/2024 in #fix-my-printer
v-core 4 idex
14 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/20/2024 in #fix-my-printer
v-core 4 idex
Oooooo that’s a neat idea! I like it! I will do so when I get back to work! Thank you so much! And I will let you know what I figure out
14 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/20/2024 in #fix-my-printer
v-core 4 idex
Yes I did my good Tik. Followed along with the instructions etc.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Agony on 12/20/2024 in #fix-my-printer
v-core 4 idex
14 replies