Grudniak
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/28/2024 in #ratos-support
GENERATE_SHAPER_GRAPHS generate Internal error on command
What should i use in probe? Beacon on both?
8 replies
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/28/2024 in #ratos-support
GENERATE_SHAPER_GRAPHS generate Internal error on command
Thanks
8 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
102 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 11/25/2024 in #fix-my-printer
IDEX inconcistent nozzle alignment
102 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
105 replies
RRCRat Rig Community [Unofficial]
•Created by Dayum on 11/26/2024 in #fix-my-printer
IDEX Commissioning - Endstop calibration problem?
8 replies
RRCRat Rig Community [Unofficial]
•Created by Dayum on 11/26/2024 in #fix-my-printer
IDEX Commissioning - Endstop calibration problem?
8 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 11/18/2024 in #fix-my-printer
VAOC calibration gives error: Move out of range
105 replies
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/28/2024 in #ratos-support
GENERATE_SHAPER_GRAPHS generate Internal error on command
8 replies
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/27/2024 in #fix-my-printer
Cant move carrige on idex
Easy solution just try stepper_buzz and look for not working stepper. Mine problem was that there is no motor2 and its the one with empty driver. I changed it to motor4 and now its working
3 replies
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/27/2024 in #fix-my-printer
Cant move carrige on idex
Found it
3 replies
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/26/2024 in #fix-my-printer
No beacon macros after fresh install ratos 2.1.0-rc2
I found the solution. I installed RaToS from scratch. I flashed the system onto the SD card again and performed a standard configuration using the configurator. Then, in the "Machine" tab, I first updated only RaToS, followed by updating the Beacon separately, and finally ran "Update All Components." Now everything works as expected.
Previously, during the fresh installation, I used "Update All" immediately instead of updating step by step (RaToS > Beacon > All). It seems that the Beacon was updated before RaToS, which likely caused the issue.
14 replies
RRCRat Rig Community [Unofficial]
•Created by Hydr0s on 11/25/2024 in #fix-my-printer
Tool head errors when going Hybrid to IDEX
click on hybrid there is start fresh button then again on idex
8 replies
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/26/2024 in #fix-my-printer
No beacon macros after fresh install ratos 2.1.0-rc2
but it is not seen after flashing boards
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/26/2024 in #fix-my-printer
No beacon macros after fresh install ratos 2.1.0-rc2
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/26/2024 in #fix-my-printer
No beacon macros after fresh install ratos 2.1.0-rc2
i can see it on devices
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/26/2024 in #fix-my-printer
No beacon macros after fresh install ratos 2.1.0-rc2
14 replies
RRCRat Rig Community [Unofficial]
•Created by Grudniak on 11/26/2024 in #fix-my-printer
No beacon macros after fresh install ratos 2.1.0-rc2
Configurator is working
14 replies
RRCRat Rig Community [Unofficial]
•Created by graceful-beige on 8/15/2023 in #fix-my-printer
Extruder Motor gets REALLY hot
same problem
2 replies
RRCRat Rig Community [Unofficial]
•Created by Skilless on 2/27/2024 in #ratos-support
adaptive bed mesh
but tell us how
14 replies