DizzySkizzo
RRCRat Rig Community [Unofficial]
•Created by Rubby on 4/8/2025 in #fix-my-print
Are these belt artifacts?
Sure, but if you want to publish the model without raw file the you need to preconfigure the refinement one time to get the STL files like we know it 😉
20 replies
RRCRat Rig Community [Unofficial]
•Created by Rubby on 4/8/2025 in #fix-my-print
Are these belt artifacts?
20 replies
RRCRat Rig Community [Unofficial]
•Created by Faulpelzrobbe on 4/13/2025 in #german-support
First Layer Problem
ja finde es leider nicht mehr in der doku ...
du druckst die first layer stl und babysteppst ind einem fall vermutlich nach oben bis es passt und gut ausschaut...
was sehr wichtig ist dass du dann noch wärend der drucker am drucken ist save_z_offset in die console eingibst dann gibt er dir auch den neuen expansion wert aus ...
nach dem drucken dann save_config
(evt. den test zur sicherheit nochmal drucken um zu sehen ob es gleichmäßig druckt und tatsächlich den richtigen abstand hat)
4 replies
RRCRat Rig Community [Unofficial]
•Created by Faulpelzrobbe on 4/13/2025 in #german-support
First Layer Problem
beacon calibrate haste vermutlich gemacht?
das anschließende Z offset hast du auch eingestellt ?
(save_z_offset) mit (firstlayer_test.stl)
4 replies
RRCRat Rig Community [Unofficial]
•Created by guesswhatsthisparlor on 4/9/2025 in #fix-my-print
What is causing this lines?
looks a bit like you are on the flow limit of that filament...
4 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
I've also tried a few, actually ... but the best results so far come from a Bambu Lab PTFE tube, 2.5–4 mm
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
Then you 100% got friction problems with your PTFE ...
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
It solves most of my fail tangle/clog detections with non abrasives/rough materials
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
I also recommend this mod:
https://www.printables.com/model/1080617-rat-rig-v-core-4-ptfe-tube-support-for-smart-senso
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
Here it is
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
[gcode_macro T0]
variable_enable_insert_detection: True # enables the insert detection
variable_enable_runout_detection: True # enables the runout detection
variable_enable_clog_detection: True # enables the clog detection
variable_unload_after_runout: True # unload filament after runout has been detected
variable_resume_after_insert: True # resumes the print after inserting new filament
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
If you're not using any abrasive material, it's probably due to a kink in the PTFE tube or because the cardboard spool doesn't unwind easily.
23 replies
RRCRat Rig Community [Unofficial]
•Created by omerk83 on 4/6/2025 in #fix-my-print
Purge blobs in the middle of a print
It looks to me like your tangle detection is reacting. That's what it looks like when I try to print with some really rough material that has a lot of friction in the PTFE tube.
That would also explain the partially stalling travel moves... it looks exactly like it does on my setup when that happens
23 replies
RRCRat Rig Community [Unofficial]
•Created by DizzySkizzo on 4/3/2025 in #fix-my-print
It goes more worse....
28 replies
RRCRat Rig Community [Unofficial]
•Created by DizzySkizzo on 4/3/2025 in #fix-my-print
It goes more worse....
Okay folks... After a bit of research in my config files I found that the two Y motors was running at different amps.... Dunno how it happened...
I reinstalled ratos because I did not get any access to the configuration tool...
So I fixed the main problem with corrected settings on the motors...
28 replies
RRCRat Rig Community [Unofficial]
•Created by DizzySkizzo on 4/3/2025 in #fix-my-print
It goes more worse....
"realtime analyser" was a good point... i dont got any acces to it or the configurator... seems i fkt up RATOS... (reinstalling it first now...)
28 replies
RRCRat Rig Community [Unofficial]
•Created by DizzySkizzo on 4/3/2025 in #fix-my-print
It goes more worse....
But I don’t understand the horizontal layer lines that only appear on the X-axis... especially since they are not present on the Y-axis, apart from the ghosting.
28 replies
RRCRat Rig Community [Unofficial]
•Created by DizzySkizzo on 4/3/2025 in #fix-my-print
It goes more worse....
Ringing/ghosting might possibly be caused by excessive belt tension, right?
28 replies
RRCRat Rig Community [Unofficial]
•Created by DizzySkizzo on 4/3/2025 in #fix-my-print
It goes more worse....
28 replies