DuBDzO
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
@heedaf this is what was suggested from @miklschmidt . Moving So when you paste new limits in before the defaults, the defaults take precedence. I was told to put everything at the end and that’s worked other then a random error at the end but . The prints completing with is what was important .
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
Odd, yes followed the commission guide as suggested for a second time. Did the the PID’s just like how the commission guide suggest along with bed mesh And all, very odd it isn’t showing this for you guys. And after every VAOC I make sure to save ( top left square button). I’ll go again for a third try. Hmm on Friday definitely doing what you guys suggest and reporting back.
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
ok thank i will try this out on friday. and report back.
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
ok so move everything i put in that section all the way to the bottom of printer.cfg save and restart and work from that point on to see if i get any errors and to see if this fixes my current issues?
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
hmm ok i was under the impression that section i pasted it in was where anything that had to do with modifying had to be pasted , because if not i would get errors.
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
trying to get this expensive and beautiful paperweight up and running 🥲
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
oh damn. ok thank you for guiding me to the degbug file at least
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
a little Morning Bump
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
mornig all
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
Good morning hope everyone is doing well. starting off a new day with some hope in resolving this hickup in hopes to get to printing.
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
sorry getting extreme brain fog
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
hmm only see enable debug
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
before i exit anything anything what can i send or do. the rage is creeping in.
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
ok soo.... same BS at the EXACT same layer like the level of frustration is really getting to me. the time and money just being dumped into this and not getting anywhere is next level upsetting
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
OK finnaly have time to test this print out again after doing the IDEX commissioning all over again. I will admit before i even re calibrated i selected the IDEX PARK macro after homing and I never got an error so i am nervous to see the same issue come upl.
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
Ok will do. Then report back. Thank you
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
in the meantime after the calibration is done.. is there a way to see if the print may end up failing again before i print or will i have to print to see if i get this code ?
41 replies
RRCRat Rig Community [Unofficial]
•Created by DuBDzO on 1/14/2025 in #ratos-support
Print stopping at lay 451 with move out of Range
ok ill test this out when im back in town on friday. It is a dual filament print with both heads in use.
41 replies