McSneaky
Explore posts from serversRRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
There are still some bad parts, but that's coz I started printing on existing debri I had on bed. Quite surprised it finished printing in first place..
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
A lot better!
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
Thnx!
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
But so far, seems to be all good
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
I started slightly bigger part.. Still 20 minutes to go
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
😄
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
It's currently heating, will see in some hours 🙂
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
First layer was all good for me before too. Only top gets messy
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
Is there any way to compare profiles?
I'd like to compare all settings between two printers
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
Lemme find that setting and try to re-print
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
Sure, gimme a sec
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
31 replies
RRCRat Rig Community [Unofficial]
•Created by McSneaky on 10/22/2024 in #fix-my-print
Gaps on top layer with .6mm nozzle
I had / have that selected. Selected it at start when I did initial setup
31 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 7/1/2024 in #fix-my-print
Rough start...
That macro would be real interesting. I was just thinking about something similar (adjusting z offset automatically in time, if I know it's always 0.2mm over 10 minutes)
Macro would be even better tho, but I have no idea how to make it myself 😅
81 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 7/1/2024 in #fix-my-print
Rough start...
Googleing for "bed mesh not compensating klipper" then you get pile of similar issues. Some people told they got theirs fixed by replacing leadscrews with ball bearing ones, coz they had less play and allowed for more precise bed movement. I haven't tried that myself
81 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 7/1/2024 in #fix-my-print
Rough start...
I have had same issue with different printers for years. What's interesting is that I get less of it on heated chamber higher temp prints. My guess has been that it's thermal expansion in frame itself, which just happens to stabilize more when whole printer is heated
It would be real cool to find the root cause for it
81 replies
RRCRat Rig Community [Unofficial]
•Created by Vindikkator on 7/21/2024 in #fix-my-print
Pillowing on very top surface
Both slicers have setting to turn down the internal bridge flow. It doesn't seem to be working in Orca tho
18 replies