DasSammy
RRCRat Rig Community [Unofficial]
•Created by modern-teal on 1/6/2025 in #german-support
RatOS
Weil einmal fettfingern wenn du nochmal in den configurator gehst und alle deine custom änderungen in der printer.cfg sind weg :kekw:
16 replies
RRCRat Rig Community [Unofficial]
•Created by conscious-sapphire on 1/6/2025 in #german-support
RatOS
Dann ist selbst wenn du dich mal vertippst falls ne Änderung kommt auf der sicheren seite da du nur das include wieder rein packen musst und nicht alles wieder zusammenschnibbeln
16 replies
RRCRat Rig Community [Unofficial]
•Created by xenial-black on 1/6/2025 in #german-support
RatOS
Was du auch machen kannst in die printer.cfg
Machst du nen [include UserOverride.cfg]
Und dann erstellst du ne UserOverride.cfg
16 replies
RRCRat Rig Community [Unofficial]
•Created by fargo on 12/23/2024 in #german-support
Firmware Shutdown: MCU Defekt?
Was die heizungen angeht hast mal versucht einfach 5 grad höher einzutippen wie der sensor liest also 25 raum temp und auf 30 einstellen?
Wenn du den RC neu aufgesetzt hast ist dein pid auch weg...
15 replies
RRCRat Rig Community [Unofficial]
•Created by fargo on 12/23/2024 in #german-support
Firmware Shutdown: MCU Defekt?
Uart
Du hast das board ersetzt richtig?
Check mal wie die Jumper sitzen unter den treibern?
15 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/3/2025 in #ratos-support
RatOS on AWD VzBot Triple Z motor configuration.
Well with beacon thats easy
Just follow the guide
And if you run a smooth pei
Go for the backside or the textured
6 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/3/2025 in #ratos-support
RatOS on AWD VzBot Triple Z motor configuration.
Problem is that awd and hybrid is different hybrid has additional 2 steppers for Y
Awd is additional steppers for x and Y
6 replies
RRCRat Rig Community [Unofficial]
•Created by heedaf on 12/27/2024 in #fix-my-printer
Hotend moving back and forth.
during first setup of beacon you gonna run a Thermal Expansion test
if that is negative you should check your mounting of toolhead and hotend/beacon
but if you are saying the top 4 screws on the hotend are tight
check the 3 holding the heaterblock
8 replies
RRCRat Rig Community [Unofficial]
•Created by DasSammy on 12/22/2024 in #ratos-support
RatOS 2.1 Pi-Cam V1.3
19 replies
RRCRat Rig Community [Unofficial]
•Created by heedaf on 12/27/2024 in #fix-my-printer
Hotend moving back and forth.
Thermal expansion
Also did you notice anything while setting up your beacon?
Like a negative thermal expansion ?
8 replies
RRCRat Rig Community [Unofficial]
•Created by heedaf on 12/27/2024 in #fix-my-printer
Hotend moving back and forth.
Also your duct is dmgd did you crash somehow?
8 replies
RRCRat Rig Community [Unofficial]
•Created by heedaf on 12/27/2024 in #fix-my-printer
Hotend moving back and forth.
Check the 3 screws from the heatbreak also
8 replies
RRCRat Rig Community [Unofficial]
•Created by DasSammy on 12/22/2024 in #ratos-support
RatOS 2.1 Pi-Cam V1.3
19 replies
RRCRat Rig Community [Unofficial]
•Created by DasSammy on 12/22/2024 in #ratos-support
RatOS 2.1 Pi-Cam V1.3
I tried a lot now... Nothing seems to work
Is there anything else i could use then crowsnest?
19 replies
RRCRat Rig Community [Unofficial]
•Created by DasSammy on 12/22/2024 in #ratos-support
RatOS 2.1 Pi-Cam V1.3
19 replies
RRCRat Rig Community [Unofficial]
•Created by DasSammy on 12/22/2024 in #ratos-support
RatOS 2.1 Pi-Cam V1.3
19 replies
RRCRat Rig Community [Unofficial]
•Created by DasSammy on 12/22/2024 in #ratos-support
RatOS 2.1 Pi-Cam V1.3
19 replies
RRCRat Rig Community [Unofficial]
•Created by DasSammy on 12/22/2024 in #ratos-support
RatOS 2.1 Pi-Cam V1.3
19 replies