KiemPlant Comments - Answer Overflow

KiemPlant

Posts Comments

RRCRat Rig Community [Unofficial]

•Created by RyeRye on 10/22/2024 in #fix-my-resonance

VC4-400 Initial Core XY graph

But you'll probably be fine

21 replies

RRCRat Rig Community [Unofficial]

•Created by RyeRye on 10/22/2024 in #fix-my-resonance

VC4-400 Initial Core XY graph

Hmm, I said that because the guide also says

Hybrid Belts
Tuning all belts from the ground up is a nearly impossible job, so Rat Rig recommends that you first tune your CoreXY belts and only then proceed to add and tune the Y belts.

Hybrid Belts
Tuning all belts from the ground up is a nearly impossible job, so Rat Rig recommends that you first tune your CoreXY belts and only then proceed to add and tune the Y belts.

And running shaper graphs before adding Hybrid basically allows you to spot issues like binding and such in time. I have no idea why they put that section before the input shaper section, as if you experience binding after already having added the hybrid belts it might be a pain in the butt to figure out what's actually causing it.

21 replies

RRCRat Rig Community [Unofficial]

•Created by RyeRye on 10/22/2024 in #fix-my-resonance

VC4-400 Initial Core XY graph

You could do that, yeah. Generally it's recommended to properly tune your belts in CoreXY configuration before adding hybrid. But then again you can simply loosen up the hybrid belts and do the CoreXY belts before tensioning the hybrid belts.

21 replies

RRCRat Rig Community [Unofficial]

•Created by RyeRye on 10/22/2024 in #fix-my-resonance

VC4-400 Initial Core XY graph

Not that your graphs are bad, but it helped me a lot with further problems.

21 replies

RRCRat Rig Community [Unofficial]

•Created by RyeRye on 10/22/2024 in #fix-my-resonance

VC4-400 Initial Core XY graph

21 replies

RRCRat Rig Community [Unofficial]

•Created by RyeRye on 10/22/2024 in #fix-my-resonance

VC4-400 Initial Core XY graph

I'm not sure if you're familiar with tuning the belts by plucking them and checking the resonant frequency using the real-time analysis tool? But here's a reference that will help you with that: https://discord.com/channels/582187371529764864/1223286652949106748/1272625387871928494

21 replies

RRCRat Rig Community [Unofficial]

•Created by RyeRye on 10/22/2024 in #fix-my-resonance

VC4-400 Initial Core XY graph

Ah yes, that makes sense.

21 replies

RRCRat Rig Community [Unofficial]

•Created by RyeRye on 10/22/2024 in #fix-my-resonance

VC4-400 Initial Core XY graph

Mine looked similar to your initial one, cause was improperly tensioned belts and also a skewed gantry. A shaper calibration would be useful to do next I think.

21 replies

RRCRat Rig Community [Unofficial]

•Created by RyeRye on 10/22/2024 in #fix-my-resonance

VC4-400 Initial Core XY graph

What did you change? Did you properly tension the belts, because it looks much better in the last one

21 replies

RRCRat Rig Community [Unofficial]

•Created by KiemPlant on 10/5/2024 in #fix-my-resonance

VC4 500 - Looks all over the place

Should I keep it that way or adjust the tension?

84 replies

RRCRat Rig Community [Unofficial]