jurassicplayer
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
Controller_fans are like ones that cool stepper motor controllers or if you want another fan to run when a certain heater is on
86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
The print cooling fan has to be
[fan]86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
The
[controller_fan] sections don't refer to the print cooling fan86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
And then add one of the following to the
USER OVERRIDES
86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
Keep the original include for the fan (the
[include RatOS/4pin-fans/part-cooling-fan-100hz.cfg]) in the fan section86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
The lines that I put or the include that blacksmithforlife mentioned should be put in the
USER OVERRIDES area86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
No, just literally what I posted
86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
as an override
86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
maybe try testing with just
86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
4p_fan_part_cooling_pin86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
I think the toolboard configs override the fan pins with ones for the toolhead
86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
For the part cooling fan in the override section
86 replies
RRCRat Rig Community [Unofficial]
•Created by Synapsis on 3/4/2024 in #ratos-support
Part Fan not working as it should
shouldn't it just be
[fan] instead of [controller_fan]?86 replies
RRCRat Rig Community [Unofficial]
•Created by TrainingMatador on 2/13/2024 in #ratos-support
Manta M8p 2.0
For the pi it's pin 5 & 6 (reset and ground)
447 replies
RRCRat Rig Community [Unofficial]
•Created by TrainingMatador on 2/13/2024 in #ratos-support
Manta M8p 2.0
If it's constantly being powered
447 replies
RRCRat Rig Community [Unofficial]
•Created by TrainingMatador on 2/13/2024 in #ratos-support
Manta M8p 2.0
IIRC the pi (and I guess CB1) will be in a state where to power the pi back on after shutdown, you need to short a pin
447 replies
RRCRat Rig Community [Unofficial]
•Created by TrainingMatador on 2/13/2024 in #ratos-support
Manta M8p 2.0
Like actually cut off power
447 replies
RRCRat Rig Community [Unofficial]
•Created by TrainingMatador on 2/13/2024 in #ratos-support
Manta M8p 2.0
Did you power cycle?
447 replies
RRCRat Rig Community [Unofficial]
•Created by TrainingMatador on 2/13/2024 in #ratos-support
Manta M8p 2.0
You already selected a template?
447 replies
RRCRat Rig Community [Unofficial]
•Created by TrainingMatador on 2/13/2024 in #ratos-support
Manta M8p 2.0
Looks like I mentioned what to include in the printer.cfg
447 replies