3D Buddy
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/8/2024 in #ratos-support
Problems during installation
Oh cool thank you 👍🙂
27 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/8/2024 in #ratos-support
Problems during installation
I just have one small question. The printer now does the Pam across the entire print bed. How can I change it so that it only does it on the area where I am printing?
27 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/8/2024 in #ratos-support
Problems during installation
27 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/8/2024 in #ratos-support
Problems during installation
Hello. I re-flashed the board and set the time zone with sudo raspi-config to Berlin via ssh, then clicked done and exited the menu. Now I've restarted the Pi and it's showing me 12:30pm instead of 5:30pm. Why doesn't the time change?
27 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/8/2024 in #ratos-support
Problems during installation
27 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/8/2024 in #ratos-support
Problems during installation
27 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/8/2024 in #ratos-support
Problems during installation
Thank you very much Mikl, I will try that tomorrow and see what happens 🙂👍👍👍
27 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/8/2024 in #ratos-support
Problems during installation
27 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/8/2024 in #ratos-support
Problems during installation
Yes I have connected it with Lankabel at the beginning there is also a connection with Klipper but it disconnected
27 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/5/2024 in #german-support
Ebb 42 1.2 defekt
10 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/5/2024 in #german-support
Ebb 42 1.2 defekt
10 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/5/2024 in #german-support
Ebb 42 1.2 defekt
Nachdem ich jetzt den Drucker neu installiert habe läuft nix mehr ich habe die neue ratos version geflasht dann compiliert dann den Drucker ausgewählt aber er lässt sich weder updaten noch sonst was irgendwie startet klipper nicht er kann auch nicht auf mein board zugreifen Octopus 446 Pro obwohl ich es neu geflasht habe.
10 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/5/2024 in #german-support
Ebb 42 1.2 defekt
Hab mir jetzt ein Ebb 42 1.1 geholt da das 1.2 nicht so schnell verfügbar war .
10 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/5/2024 in #german-support
Ebb 42 1.2 defekt
Es soll nur gegen das defekte EBB42 1.2 getauscht werden es ist schon alles in der Printer cfg vorhanden
10 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 5/5/2024 in #german-support
Ebb 42 1.2 defekt
Habe ein Octopus Pro 446 Board mit Rapido Plus UHF und Orbiter 2.0 Extruder
10 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 4/21/2024 in #german-support
Z Out of Range
Supi danke dann ändere ich das 🙂👍
6 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 4/21/2024 in #german-support
Z Out of Range
das ist die cfg
6 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 4/21/2024 in #german-support
Z Out of Range
Sorry muss ich morgen machen komme heute nichtmehr in meine Werkstatt habe nichts geändert und meine Gehäuse von 270mm Höhe hat er bis jetzt problemlos gedruckt mir ist es nur aufgefallen weil ich die Materialspule innen an die Seite gemacht habe um zu sehen ob der Platz für meine Gehäuse von 270mm dann noch reicht.
6 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 7/14/2023 in #german-support
Temperatur out of range
Ich glaube es hängt mit dem Thermistor vom Heizbett zusammen ging auf Störung beim Bett aufheizen kann man den Thermistor getrennt wechseln oder braucht man ein neues Heizbett?
5 replies
RRCRat Rig Community [Unofficial]
•Created by 3D Buddy on 7/14/2023 in #german-support
Temperatur out of range
5 replies