TheSenate
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
Can I simply have the heater bed plugged into the octo board, but not wired up to the power supply and all that?
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
(I don't have it plugged in, I thought you're supposed to have it unplugged for the first comissioning)
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
Testing now
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
That's why I was confused, I think you missed this
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
But in that message from earlier, I said I noticed it was in the wrong slot, so I swapped
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
It wasn't in the original picture I sent
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
Would it really not work without a jumper though?
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
Correct, my jumper is in that slot
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
If so -- my wiring appears correct...
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
I don't understand, are you saying my wiring is incorrect? Is it orange = thermistor, blue wires = hotend? (in the context of the diagram, in real life the colors are different)
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
I didn't swap the thermistor/hotend cables, I swapped the entire rapido v2 hotend with another fresh one, and then instead of crimping cables like in the guide, I tried this time to use the pre-crimped cables that come with the hotend, in case there was a bad wire job/crimp/thermistor
30 replies
RRCRat Rig Community [Unofficial]
•Created by TheSenate on 2/17/2025 in #fix-my-printer
MCU 'toolboard_t0' shutdown: ADC out of range
I believe my image reflects this placement, does it not? I just noticed though my jumper was in the other slot though, swapping and testing to see if that does anything
30 replies