truckdoor
RRCRat Rig Community [Unofficial]
•Created by archen on 4/1/2024 in #fix-my-print
inconsistent overlap/bridge
Okay I guess it works. I hoped there was a "Dont do retarded bridges" checkbox somewhere
11 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 4/1/2024 in #fix-my-print
inconsistent overlap/bridge
If you find out, let me know :p
11 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 4/1/2024 in #fix-my-print
inconsistent overlap/bridge
Im not sure, this should be a common enough problem that there is a slicer setting that fixes it
11 replies
RRCRat Rig Community [Unofficial]
•Created by archen on 4/1/2024 in #fix-my-print
inconsistent overlap/bridge
Is the print direction of the bridge the same? It looks like one takes the long way, and the other the short
11 replies
RRCRat Rig Community [Unofficial]
•Created by truckdoor on 3/27/2024 in #fix-my-print
Bendy corners on the enclosure magnet frames in ABS enclosed
Maybe mount it to the bottom plate facing upwards, and drill a small hole for wires
18 replies
RRCRat Rig Community [Unofficial]
•Created by truckdoor on 3/27/2024 in #fix-my-print
Bendy corners on the enclosure magnet frames in ABS enclosed
I actually looked at that mod too. Im considering doing about the same, with a thermal fuse, thermistor and a control board outside the printer
18 replies
RRCRat Rig Community [Unofficial]
•Created by truckdoor on 3/27/2024 in #fix-my-print
Bendy corners on the enclosure magnet frames in ABS enclosed
I promised myself that my new printer bed wouldnt be a flytrap, so I will try all alternatives before going that route :p
18 replies
RRCRat Rig Community [Unofficial]
•Created by truckdoor on 3/27/2024 in #fix-my-print
Bendy corners on the enclosure magnet frames in ABS enclosed
Can I see a picture of your setup? How do you control it?
18 replies
RRCRat Rig Community [Unofficial]
•Created by MACBEAN on 3/31/2024 in #fix-my-print
What is making my corners look like this?
Which pressure advance calibration method did you use?
5 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/27/2024 in #fix-my-print
nozzle hitting print
Glad you got it fixed, and thank god it wasnt some problem with the z motors or z screws
66 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/27/2024 in #fix-my-print
nozzle hitting print
Yes, and it looks like hes using the short one
66 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/27/2024 in #fix-my-print
nozzle hitting print
The sock on mine is a lot further down
66 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/27/2024 in #fix-my-print
nozzle hitting print
Hmm I dont have the new toolhead, but are you using the UHF sock?
66 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/27/2024 in #fix-my-print
nozzle hitting print
I later replaced it with a 24V 4020 fan, that I could connect directly to my toolboard, since I didnt need the full cooling the 4028 provides anyway
66 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/27/2024 in #fix-my-print
nozzle hitting print
Because I had to set it to 10% min, 30% max for my PETG prints
66 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/27/2024 in #fix-my-print
nozzle hitting print
Is it the stock 4028 fan from the kit?
66 replies
RRCRat Rig Community [Unofficial]
•Created by truckdoor on 3/27/2024 in #fix-my-print
Bendy corners on the enclosure magnet frames in ABS enclosed
I know this is out of scope, but do you have a heated chamber? I have a 12v ptc heater and fan, but I’m not sure about the best location inside the enclosure. Maybe in the bottom?
18 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/27/2024 in #fix-my-print
nozzle hitting print
And if possible, check the travel distance on each of the lead screws separately, if its one of the motors, it cant possibly be all of them
66 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/27/2024 in #fix-my-print
nozzle hitting print
Except a loose connection?
66 replies
RRCRat Rig Community [Unofficial]
•Created by Brandon on 3/27/2024 in #fix-my-print
nozzle hitting print
I cant think of anything that would explain why the lead screws random rotates MORE than expected
66 replies