RatOs invalide
Hi!
I’m triying since the morning to install RatOs as explain on the website but I m not able to update RatOs or RatOs configurator. On the picture you can see that the both are invalid… soft or hard recovery have no effect
36 Replies
Restart moo raker. Hard refresh the browser (ctrl+shift+r) and refresh the updates
Either soft or hard recovery will break it.
You need to ssh and restore everything or flash again the sd card.
I tried to connect ssh but not working ???
Same ip from the machine?
Or using the hostname?
The both not working
Never have this problem on others
I would flash the sdcard again
I did it 4 times ….
And no ssh?
The 4 times?
Can you try on commandline?
Send
ssh pi@machine_ip
putty wants the hostname or IP,
http is for websites, not sshNothing …
I know I just tried the both to be sure but nothing
I don t under stand what s happened… just flash the file on my card with balena etcher
Either something on your netword and/or computer is messing ssh access…
what's the IP of the computer you are using for SSH? And what is the IP of your raspberry pi?
I use a ip scanner to find the ip of RatOs rp and use this one for ssh
I am trying to figure out if you are on the correct subnet - but I can't if you refuse to give us the IP address. Your local address is only good for your network if you are worried I am trying to attack you or something
I Could now ssh connection with the rpi
What do I have to do now ?
Then RatOs is up to date but impossible to make the same with ratos-configurator
if you can ssh in, have you tried to run
ratos doctor?Command not found
Try this then:
Not working …
I think I flashed 10x ... I have 4 printer on ratos without any problem... and now so painful to make something good
Try this, line by line:
ssh to the machine
cd printer_data/config/RatOS
git fetch origin
git checkout -b v2.1.x origin/v2.1.x
sudo ./scripts/ratos-update.sh
cd ~/ratos-configurator
git fetch origin
git checkout -b v2.1.x-deployment origin/v2.1.x-deployment
sudo ./scripts/update.sh
sudo systemctl restart ratos-configurator
sudo systemctl restart klipper
sudo systemctl restart moonraker
Then refresh updates
I think I will stop to work with ratos... at the start it was so easy to install every thing... now is more complicated than a nuclear reactor... it is very sad
Still same problem …
it is very easy to install ratos, the above "complicated" instructions are to help you with something that went wrong. If you're getting this weird behavior after a fresh flashing of the card I would suggest getting a new card, a new pi, try on a different network... something else is interfering
Feel free…
It is very easy to criticize all the ones giving up on their time for this.
Literally thousands of people using it.
I don't critic all the work done... just say it s more easy before the 2,x version...
I like very much ratos... but at this time I think it is became a little bit complecated for a lambda user.
That's all
If I blhave blessed you I apologize
no stress 😉
Again, thousands of people using it…
And that is invalid because you are missing some steps.
At least, hard refresh on the browser. Then, restart moonraker and refresh the update manager
The separation between RatOS and ratos-configurator no longer exists. For some time. So, your browser is working based on temp files. Hence the need for hard refresh
I let the pi running all afternoon because I have to leave home... and beleive me or not when I came back all is green
don't understand what's happened
Probably the browser refreshed for some reason
I should not have both RatOS and ratos-configuration. Now there is only RatOS configurator
That is correct
So, tell me now, not that hard 😉
😉
Soon this will be a non issue. As soon as the final version image gets done.
This was a big update from Rc2 to RC3 and forward
now have to flash the prusa mini... I think another shit to do 🙂