manta m8p V1.1 install
Well first to say hi to all just found this site and glad to be here.
Also i'm no expert on Klipper.
I have a Manta M8P V1,1, CB1 and a Ebb42 V1.2
I followed the setup RatOS setup guide Installed the board then installed the Ebb42 which it flashed in DFU mode. Opened Maisail did all the updates etc. Then I installed the V core Three and well here my problems began. So with the help of someone else who has the Manta M8P running sent me his setup to following. I tried using his config but still nothing Klipper will not connect and after a bit I get a mcu error.
It does not say what is wrong like. To try and find the problem I have not connected the EB42 yet but have only the basics.
Any help as how to track down the problem is welcome.
35 Replies
Please upload your printer.cfg
Hi thanks for the quick replay these are the printer config and custom config, I know I have to change the part where i'm using the Bl Touch and not the probe. This config was to see if it was working even if my inital idea is to use the EBB42 which i flashed durng the RatOS install. Thanks for your help
Why do you have a custom config? Manta 1.1 is supported now
see https://github.com/Rat-OS/RatOS-configuration/tree/v2.x/boards/btt-manta-m8p-11
just uncomment in the printer.cfg https://github.com/Rat-OS/RatOS-configuration/blob/v2.x/templates/v-core-3-printer.template.cfg#L27
Hi that was the first thing I tried but go errors. I will try again see what errors I get. thanks for now
make sure to update Ratos and the others in the machine tab first
Ok just updated in the dashboard eveything. Started from Step 1 said i had theManta m8p v.1.1 and flashed it via DFU then it asked to install toolboard selected my version and flashed it in DFU continued
Chanaged my setting in the printer cfg but i get Klipper trying to connect then a little bi tlatemcu error.
upload your new printer.cfg
ok here it is
question i still have to connect the endstop will that cause a oprobklem?
and what is the error you are getting (screenshot)?
you also need to include line 99. The toolboard include on line 294-295 just overrides the defaults from line 99
ffrist klipp then mcu
ok include 99
that first klipper one is normal and not an error. The unable to connect to MCU means either it didn't flash correctly or the USB connection isn't good. What is the output of
lsusb?moment
i connected via can bus to the Ebb42
ok so it is connected. what is the output of
ls /dev/btt-manta-m8p*?ls:command not found
/dev/btt-manta-m8p
sorry
ahh, yeah it still has the old firmware on the manta board
left th equestion mark
?
it should be
/dev/btt-manta-m8p-11so it didn't flash like it said it did
ok so the configurator screwed up or me
I started setup from step 1 selected my board and flashed it
sorry maybe i screwed up
i may have selected the worng board
am now flashin the correct board
ok my bad flashed th ewrong one now i have /dev/btt-manta-m8p-11
now i getb this because i would think its not seeing the temester
make sure it is plugged into the correct port and has the correct type defined
i shuld have the 100k it was the one i was using with my duet 2 wifi
have to check the dip switch
thanks so much could i offer you a beer or something
https://www.klipper3d.org/Config_Reference.html#common-thermistors
that is very kind of you, but just pay it forward. That is what makes this community so great
sorry but the v& uses a Semitec 104NT which shows in the v6.cfg question on the Ebb42 there are two themister ports on TH0 and the other PT100 or PT 100 i'm not sure where the hotbed themistor goes i used the TH0 the other
I tried PT100 should i use PT1000? can't find anything thats ckear
you just need to override for your specific setup. So in the
USER OVERRIDES section you would add
strange on the touch scree i see this but not in the browser
ahh so it is the bed heater one
So in the
USER OVERRIDES section you would add
ok thanks
Thanks so much!👍
Not important but can you change the name from Raspberry Pi to CB1 in Mainsail?
not in mainsail - you would have to make your ratos install dirty to do it (not recommended as it causes other problems). I did create https://github.com/Rat-OS/RatOS-configuration/pull/104 so if you want this functionality I would contact @miklschmidt and up vote it
There's no good way to do this currently without significantly increasing complexity or ugly hacks so it's a cosmetical problem you'll have to deal with for now, unfortunately.
Ok like I said not important. Thanks for the reply.