codafoo
codafoo
TTyperactive.xyz
Created by codafoo on 12/12/2024 in #🛟-help
Right side - corne premium case 2 rows stopped working while it was charging
@Calagius They have a nice!nano in testing that has grounding to the usb shield but I’m not sure when the timeline for release is.
39 replies
TTyperactive.xyz
Created by waitwhat on 3/23/2025 in #🛟-help
Help building no solder board
fyi those are not the no solders they come in a different bag
13 replies
TTyperactive.xyz
Created by jarrod on 3/23/2025 in #🛟-help
corne 42 wireless not working
the nice nano is supposed to be facing the other way
11 replies
TTyperactive.xyz
Created by codafoo on 12/12/2024 in #🛟-help
Right side - corne premium case 2 rows stopped working while it was charging
i guess it wouldn't be temporary maybe alternative would be a better way of saying it as my only issue is the ESD.. i also sprayed my floor with anti-static spray too so I think my office is relatively safer now 🤣
39 replies
TTyperactive.xyz
Created by codafoo on 12/12/2024 in #🛟-help
Right side - corne premium case 2 rows stopped working while it was charging
Hey @Nicell, just checking are there any updates with grounding the nice!nano's usb connector? i took apart the keyboard only to realize I don't have any nano's or headers to replace it with to go for Maba_Kalox's temporary fix
39 replies
TTyperactive.xyz
Created by codafoo on 12/12/2024 in #🛟-help
Right side - corne premium case 2 rows stopped working while it was charging
Thanks! I was thinking of doing the same using a ring terminal but not sure if a have one that is small enough. 🤔
39 replies
TTyperactive.xyz
Created by codafoo on 12/12/2024 in #🛟-help
Right side - corne premium case 2 rows stopped working while it was charging
@Maba_Kalox have you had anymore issues how did you connect the case to ground?
39 replies
TTyperactive.xyz
Created by codafoo on 12/12/2024 in #🛟-help
Right side - corne premium case 2 rows stopped working while it was charging
FYI I'm back at home so ready to test any updated nanos when they are ready 🥳
39 replies
TTyperactive.xyz
Created by codafoo on 12/12/2024 in #🛟-help
Right side - corne premium case 2 rows stopped working while it was charging
@Nicell fyi on vacay for 2 weeks
39 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
but you might have just been unlucky to have gotten a bad controller I would e-mail them about it and see what they say
33 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
physically bridge it that is
33 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
33 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
and then you would define it in the col-gpios
33 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
@splitdev yes, it's not too bad, first you'd have to bridge the column to a working pin
33 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
p104 for example
33 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
i think you can message support about it and they will replace, and there are also free gpio pins
33 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
depends on the environment (if you have a lot of static)
33 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
you don't have the premium case do you
33 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
ya that gpio pin might be dead
33 replies
TTyperactive.xyz
Created by splitdev on 12/16/2024 in #🛟-help
soldering help needed - one column doesn’t work
yes i would test pins on bottom first as that is what should be connected to your PCB, then if those don't work test on the micro controller
33 replies