RimanDk
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
By all means, go for it! If you make inroads, that's helpful to me, too! =)
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
Yes/no/maybe? I have had the undervoltage line show up for just the one motor that disconnected whne it wasn't both. Before I hit the e-stop. That was with a different fw, though (early 1.17)
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
Worth noting that I have also tuned down my damper frequency setting from the default 25Hz to something like 12, if memory serves. The issue appears to be related to damping and/or inertia settings. Dialing those filter frequencies down helps.
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
Walmis and I tried a few things, including upgrading firmware on the motors themselves, but the problem persists. Last i heard, he was working on a new revision of the Rhino fw that would put the issue to rest, but that was before Christmas and nothing yet.
I'm still struggling with the problem, though to a lesser extent since the motor fw upgrade.
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
Okay, had a 2 hour 30 session with the abovementioned changes and the problem did not manifest. Looking at the Debug tab, I saw a single entry of undervoltage fault, but I think the time code coincided with me powering down the device.
Obviously, a sample of 1 is not a guarantee, but seems good so far. I will continue having sessions as close to daily as I can for the rest of the week and report back how it goes.
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
I'll have a session tonight and report back if these changes did anything
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
Okay - lowered that to 15 Hz and removed inertia and friction from my settings.
All hardware plugs appear fine, both joystick-side and PSU-side.
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
I have tried removing inertia. Which part is Damper LPF?
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
I am flying with TelemFFB, yes.
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
@walmis is it possible to revert to an earlier firmware? It would help figure out if my issue is hardware or software related.
If it is hardware-related and we think it's the PSU, is it possible to source a replacement?
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
I had the damping forced turned up, because this happened while I came across the other issue I mentioned separately. That is, I had no ffb and nothing on the trim functionality. So, I was flying the Apache in DCS, feeling vibrations and "dead stick forces" basic damping and inertia from VP Configurator, but pressing the trimmer didn't set a center at all.
This happened in multiplayer after I checked that I had forces and trimming worked, in the Huey free flight instant mission (usually, it's a good sign if I have ffb there; if I don't, I restart DCS and I usually have forces back).
That is to say that there were minimal forces on the stick at the time the fault above happened.
34 replies
VCVPforce Controls
•Created by RimanDk on 11/1/2024 in #🧰support
Undervoltage
Adding in the 25% damper and 15% inertia, I'm seeing roughly the same results.
34 replies