TheSecondKen
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
Need to find some way to get the M1/M2 buttons to output some unique event that can be read in bazzite/hhd. I can send the command to switch modes, but I think MSI is doing some weird things with the M Buttons, because even with stock ubuntu, there are no raw events coming off of those buttons.
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
Which is the same behavior I was seeing with the M keys. I could only get hid events when it was sending other keys
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
I'm not sure, I have to try it again and see what the hid payload is, it might just be the mouse event/joystick event
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
Wireshark on the controller gives me data when the gyro is active, but I'm not seeing commands to activate it so no idea where they're coming from
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
Ah, gotcha. I have the ally X with the focaltech with no Linux support at all. Fixing my dual boot at the moment so I can Wireshark and then switch to bazzite.
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
ok, so the 3cfe is the calibration acknolwledgement, i need to find the gyro activation command.
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
ran sudo hhd.contrib hidraw 6
then in another terminal i ran sudo hhd.contrib hidraw 6 0f00003cfd020000, and in the first terminal i got 1000003cfe00000000000000000 back. not sure if im doing this right. wasnt getting like a stream of data and moving the device around didn't seem to do anything.
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
currently reinstalling bazzite to test the gyro stuff, but i have a bit of a dumb question. I know on the Ally, the fingerprint reader is not supported. that one is a FocalTech, but on the Claw, it has a Goodix MOC that seems to have support in libfprint. is there anything special I would need to do to enable fingerprint reader on bazzite?
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
thanks
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
turns out there was new firmware.
OK, when running calibration the host sends 0f00003cfd020000 during the gyro calibrate step. in bazzite, how would I test this to see if the gyro starts sending data?
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
Funny enough, I have the calibration menu, but not the gyro options menu. The calibration menu doesn't work at all on my device. need to figure out why, then I can poke and see what if any commands the calibration is sending to the HID device.
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
I guess it would be longer than the other commands due to setting colors and stuff
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
But yeah I found that hid data in my Wireshark, and it looked weird to me
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
It's probably the three zones. (LStick, RStick, face buttons)
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
Ah. Ok I'll test that too.
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
RGB and back buttons are the last two areas I believe need figuring out from a pure controller standpoint. I'll poke around when I have a chance, I just have a lot of stuff going on
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
still working on RGB commands. need to work on my wireshark filtering.
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
I'll play around with RGB stuff next, probably late Thursday or Friday EST
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
Poking around in Wireshark and in Linux, right now im not sure if the back buttons are possible to map. Regardless of being in combo or macro mode, Linux doesn't seem to see any events and Wireshark only fires stuff in macro, but the events being fired are the key presses defined in the macro. And when setting the mode, the only thing that changes is the 240101 vs 240100. I feel like there is a raw event somewhere, but no idea which device would even fire it.
504 replies
UBUniversal Blue
•Created by HikariKnight on 8/20/2024 in #🛟bazzite-help
Attempt to add MSI Claw support?
I'll try and see if I can get any response out of the buttons in bazzite after poking around with Wireshark
504 replies