Installing Firmware error

I'm getting the following error on the right and left board when trying to copy and paste the pre-compiled firmware. Any advice?
No description
29 Replies
TyperAI
TyperAI•4mo ago
It sounds like you're having trouble flashing the firmware. What is the error you're seeing? Also, make sure you're entering the bootloader by double-tapping the reset button before dragging the .uf2 file to the NICENANO drive. You can find more info on flashing the firmware here: https://docs.typeractive.xyz/build-guides/corne-wireless/firmware#installing-firmware Let me know if that helps or if you have any other questions!
Firmware | Typeractive.xyz Documentation
If you're not familiar, ZMK is a wireless-focused firmware, and it powers our Corne Wireless.
TheDanMonster
TheDanMonsterOP•4mo ago
Error 0x800701B1
PurpleTaro
PurpleTaro•4mo ago
super lazy/quick test - try a different USB port and/or cable? I think i got that once when i had a way-too-long extension cable
TheDanMonster
TheDanMonsterOP•3mo ago
Tried that. I think my soldering job was crap - my solder wire diameter was too large to be effective (that and I suck). Got some thinner/better wire, going to clean it up and try it again. Will post back if that doesn't work Still no dice. Damn.
TheDanMonster
TheDanMonsterOP•3mo ago
updated error
No description
PurpleTaro
PurpleTaro•3mo ago
mini-longshot, what if you pull a nice!nano? (i assume they're the board) if it's not in anything, then it'll isolate it down further
TheDanMonster
TheDanMonsterOP•3mo ago
What do you mean "pull"? And yes, that is the board Same issue left and right, but the left all columns except 1 work fine. so weird. Alright. So now the left fully works. Screen is black. Still getting the error above when trying to copy over the firmeare
PurpleTaro
PurpleTaro•3mo ago
oh, sorry, i mean pull as in, remove it from the PCB so it's just literally the nice nano and naught else. the logic being - if it flashes when it's just plugged in to the PC and it's literally the nice nano sitting around, then yay! nd it's something else influencing things
TheDanMonster
TheDanMonsterOP•3mo ago
Ahhhh. Got it. I'll give that a shot Nope. Pulled it from the board. Used tweezers to activate the bootloader and tried to drop in the UF2 file. Still the same error. 😦
PurpleTaro
PurpleTaro•3mo ago
Hmph.. sanity check as well - this is my left/central half in bootloader mode and i can read the text file there.
No description
PurpleTaro
PurpleTaro•3mo ago
(and copy stuff off) Not a direct solve or anything, but validating something is functional
TheDanMonster
TheDanMonsterOP•3mo ago
Here is mine. I can open the TXT file too.
No description
PurpleTaro
PurpleTaro•3mo ago
UF2 Bootloader 0.5.0 lib/nrfx (v2.0.0) lib/tinyusb (0.9.0-22-g7cdeed54) lib/uf2 (heads/master) Model: nice!nano Board-ID: nRF52840-nicenano-v2 SoftDevice: S140 version 6.1.1 Date: Apr 7 2021
sweet, so we at least have something in common šŸ˜„ okay, so you probably did all of these, but i'll just enumerate incase there's a combination of note. assuming you've got the bare board, it shows, up, bla bla.. problem: when copying/drag drop the uf2 to the board you get error messages guessing/thing trying to rule out: cable/connection wackyness So that's possibly some combo of host PC port and/or cable on my computer i've got like, a spread of ports on front panel/rear panel and USB 3.0 and 3.1, USB-C and whatever else is there Same error/result on USB 2 and USB 3 ports i'm guessing? same error/result on the combination of USB2/3 and shorter/different cables?
TheDanMonster
TheDanMonsterOP•3mo ago
Hmmmm. I tried a usb a to C cable and usb c to c. I'll try ports on the back of the PC and a couple other cables as well
PurpleTaro
PurpleTaro•3mo ago
(also, am assuming this is the stock firmware from typeractive, to remove even more variation)
TheDanMonster
TheDanMonsterOP•3mo ago
Correct
PurpleTaro
PurpleTaro•3mo ago
i do not claim any of this is sensible but the USB/cable thing is quick and easy to run through all the myriad combinations, i"ve got cables that i end up just tossing into the "power only bucket" as things get flakey. (i also have a USB-C 3.1 port that absolutely sucks for some reason that i never bothered working out - my USB-C capture card does not like it at all)
TheDanMonster
TheDanMonsterOP•3mo ago
OK. Tried 2 different ports and 3 different cables on each port. Same result. Unable to drag and drop lily58_left-nice_view_adapter-nice_view-nice_nano_v2-zmk-055ed1d8b9d076ae239380a9f96912cc.uf2 to the F drive
PurpleTaro
PurpleTaro•3mo ago
righto! at least that's consistent. I hate intermittent failures šŸ˜„
TheDanMonster
TheDanMonsterOP•3mo ago
The left keyboard works, but the screen in speckled
PurpleTaro
PurpleTaro•3mo ago
cause there's connectivity stuff involved and the core thing is not being able to put firmware on, i'd almost want to go back to board-only and no other stuff anywhere in the chain. As you may guess, i'm a huge fan of trying to make the problem simpler by tossing bits out
TheDanMonster
TheDanMonsterOP•3mo ago
Yeah. That all makes sense!
PurpleTaro
PurpleTaro•3mo ago
Sorry i'm not finding you any answer, but this is sort of my tech debug process. Running out of voodoo tricks alas.
TheDanMonster
TheDanMonsterOP•3mo ago
It's all good. Just kinda weird it's happening to both nice!nanos...
PurpleTaro
PurpleTaro•3mo ago
yeah, that kinda makes me want to swap out the PC as well XD
TheDanMonster
TheDanMonsterOP•3mo ago
Hmmmmm. I got a macbook. i'll give that a shot
PurpleTaro
PurpleTaro•3mo ago
ALL THE HARDWARE! šŸ˜„
TheDanMonster
TheDanMonsterOP•3mo ago
Alright! I was able to move that over and flash the boards without any error. Now... to get the screens to work...
PurpleTaro
PurpleTaro•3mo ago
woo! okay, that's a win

Did you find this page helpful?