Overhang improvement? V-core 3.1
(Dont mind the change of color, I was testing the runout sensor.
The included photos are my slicer settings, the model is the "CURVE OVERHANG TEST" free from Cults3d. Im printing with a .4mm nozzle, .2 layer height, .4 layer width.
Is this as good as it gets? Any thoughts on how to further improve the result?...
The included photos are my slicer settings, the model is the "CURVE OVERHANG TEST" free from Cults3d. Im printing with a .4mm nozzle, .2 layer height, .4 layer width.
Is this as good as it gets? Any thoughts on how to further improve the result?...
Firmware retraction always on ?!?
Hi all, even though it's not activated in superslicer, firmware retraction always prevails during prints. Any idea ? Thanks in advance ! (v-core 3.1, Ratos)
Severe first layer problems
Hey guys, i have a pretty big problem with my first layer and I really don't know what to do
I first thought it's a problem of to less bed mesh so I upgraded my toolhead with a beacon Rev H and a 100x100 bed Mesh on my 500x500mm bed (and using adaptive meshing) but it still dosen't work.
Every time I print the brim is totally fine but then the nozzle gets closer and closer until it stops due to no filament is getting pushed forwards.
...
First Layer Problems
Hey,
having Problems with the 1 Layer (PLA)(0.6Nozzle).
-E-Steps are OK
-Temp tried from 190 to 220
-Speed from 50 to 150mm/s...
Weird Pattern on flat Walls
So I had this issue before and I'm not sure how I fixed it the last time. It's a weird Pattern on the Walls. I switched from CF-PETG to PLA and this Pattern appeared in the first print. Angled surfaces look fine, but flat ones have this pattern. I'm using a Vcore 3.1 400
First Layer / Mesh Problem
Any ideas on why I am seeing this and what I can do to correct it? Essentially One part of my first layer is fine and another part is too squished. The back in the photo is fine but the front is too squished?
Bad filament?
Hi, is my Yellow ABS bad ( wet? ) ? in blue ABS print coms out flawless eventhough blue is 7 years old. same setting/slicing
underextrusion- due to retraction?
It looks like I'm suffering some underextrusion. I think it's caused by the many retractions necessary to complete the tree support leaves on the flat surface.
How do I fix underextrusion from retractions?...
Trash First Layers
PETG I’ve been printing with for years, same files sliced for years, swapped to the new black pei plate from RR last week and could not get the print to stick even after titting around with the probe offset. So I’ve gone back to my non textured plate and original offset and I’m still getting these rubbish first few layers.
Eclipson airplanes helix printing issues.
Hi there. I'm currently trying to print the Helix RC plane from eclipson models but I'm really struggling with 1 part. It's the Wing L2 and R2 part. I have used all their recommend settings. The only difference is that I'm using orca slicer (same issue with prusa, super and cura). When I'm required to print these parts, it has to try and print on thin air basically and it's causing a lot of issues. Has anyone else had experiance with these planes/parts? I've messaged them directly but they are quite slow in response. I've attached 2 screenshots from the slicers I use. When I try and print the part in spiral mode, the parts fail at the time it's suppose to print on thin air (obviously). The parts come out a completely different shape because it's trying to print the 2 CF tube holes in mid air, this causes blobs on the side which the nozzle hits and moves the model about.
Any help would be appreciated! Settings are exactly as they are on the website, except the flow is 0.95 and not 0.53. I'm using pre foamed PLA so I don't need to reduce the flow and increase the temperature....
regular protrusions?
All my walls end up having these random protrusions, and I don't understand what could be causing it. Any clue?
I'm printing PETG, if that's relevant....
Print failed on last layers
Hi, I took a bigger print with my Vcore 400 for the first time last night. In the last layers, it failed completely. There was no adhesion on one side anymore. However, in terms of dimensions, the part is correct. But you can already see some errors beforehand. What could that be? Too low temperature? Flow rate too low? Humidity? The printer is an open Vcore 400, the slicer is Orca, and the material used was XPETG from extrudr at 220°C.
Bad surface quality with holes
I am recently having the issue, that the surface oy my prints is very bad in specific regions of the print.
All other sides of the print are fine, but the side shown in picture looks like molten / with big gaps.
Any ideas on this?...
small gaps between layers across print. can sand it but just curious what it could be.
Using 0.4 m nozzle and 0.28mm layerheight
